As-Built Drawings: Field-to-Revit Guide for Solo Architects
Key takeaways
- As-built drawings document a building exactly as constructed, including every field change that never appeared in the permitted set.
- Dimension the deltas, not the whole building, so reviewers and clients can see exactly what changed.
- Phone LiDAR plus a laser measure covers most residential capture in an afternoon, but corners and flush conditions still need a tape check.
- AI drafting can model CDs from verified dimensions overnight, but field verification stays the architect's responsibility.
- Published as-built service pricing commonly runs about $0.10–$0.25 per square foot, comparable to $1,400–$2,400 for a contract drafter on a 2,500 sq ft house.
As-built drawings document a building exactly as constructed, capturing field changes like moved walls, resized openings, and rerouted ducts that never made it into the permitted set. If you run a one-architect residential practice, you both produce them for closeout and consume them as the base for every renovation permit set you stamp.
What are as-built drawings and how do they differ from record drawings and shop drawings?
As-built drawings show the building as it was actually constructed, including every change made during construction. On a residential permit set, that means the dimensions, wall locations, and conditions that exist in the field, not the ones you drew before the contractor picked up a hammer. If you scan an existing house before a renovation and rebuild it in Revit, that measured model is the starting point for accurate as-builts, which is exactly what our scan-to-as-built workflow is built for.
What 'as-built' means on a residential permit set
For a solo practitioner, as-builts show up in two places: the existing-conditions sheets in your permit set, and the corrected set you issue after plan check or a correction letter forces a revision. Both are supposed to match reality.
Record drawings vs as-builts vs shop drawings
The AIA's E203 building information management exhibit distinguishes who produces and owns each document type.
| Document | Produced by | Shows |
|---|---|---|
| As-builts | Contractor or architect | Field-verified existing conditions |
| Record drawings | Architect | Final design intent, marked up from as-builts |
| Shop drawings | Subcontractor/fabricator | Fabrication details for specific products |
When are as-built drawings required and who is responsible for producing them?
Residential scenarios where you will be asked for as-builts
Three triggers come up repeatedly in residential work. First, permit closeout: many Washington jurisdictions require a corrected or as-built set before final inspection, especially when field changes diverge from the permitted plans. Second, renovation permits: if you are adding onto an existing house, the city expects the existing-conditions sheets to reflect what is actually there, verified in the field. Third, lender and owner requests: a homeowner refinancing, an insurance claim, or a future sale can all prompt a request for record documents showing the house as constructed.
Who signs and who owns the deliverable
Responsibility depends on who changed the drawings. If your design changed during construction, you document the changes and issue the as-builts under your seal. If the contractor made means-and-methods adjustments, they typically mark up a redline set and hand it to you; you decide what merits a revision cloud and a reissued sheet. Ownership usually follows your services agreement. Spell out in writing whether the client receives PDFs, native Revit files, or both, and what happens to the model at closeout. Pretiva's terms cover deliverable ownership for work produced in Studio (https://studio.pretiva.io/terms), and your own contract should be equally explicit.
How do you do as-built drawings step by step, from field verification to final Revit deliverable?
Step 1: Pull existing drawings and set up the Revit model first
Before anyone drives to the site, collect whatever exists: the original permit set, any resubmittal sheets, the correction letter, and prior city comments. Set up the Revit model against your office standard now, with view templates, sheet setup, and shared parameters in place, so field data lands in a model that is already shaped like a deliverable.
Step 2: Field capture with tape, laser measure, or phone LiDAR
For a residential remodel, a laser measure plus a phone with LiDAR covers most rooms in an afternoon. Photograph every wall with dimensions in frame, shoot ceiling heights, and note conditions a scan will not explain: sagging beams, patched openings, Romex where conduit should be. Sketch room-by-room plans on paper or tablet as you go.
Step 3: Resolve discrepancies and dimension the deltas
The long paragraph:
The core discipline of as-built work is dimensioning the difference, not the building. Overlay your field measurements on the original drawing and dimension only the deltas: the wall that moved four inches, the window rough opening that shrank, the stair that never matched the section. If you dimension everything as if it were new construction, the reviewer cannot tell what changed and neither can your client. This is also where you decide what the closeout actually requires. Jurisdictions differ: Seattle's Department of Construction and Inspections, for example, publishes its own permit and revision requirements that determine whether a full as-built set or a marked-up revision sheet satisfies the record (https://www.seattle.gov/sdci/permits). Check the specific city's page before you model a single wall.
Step 4: Model, sheet, and QC against the office standard
Model to your template's level of detail, cloud every change, and set up sheets exactly as you would for a permit set, because the closeout reviewer expects familiar conventions. Run a final pass: cross-check room areas against field notes, confirm revision clouds tie to a delta list, and verify title blocks. More workflow detail and templates live in the Pretiva guides library.
What must as-built drawings include to satisfy construction and closeout requirements?
A closeout as-built set needs three things on every sheet: the field-verified plan, a clear record of what changed, and a title block that shows the revision date and who verified it. Anything less and the reviewer or owner is back to asking you what happened.
Minimum sheet content checklist
For a residential permit set, each as-built sheet should carry:
- Dimensioned plans with overall and critical partial dimensions, not just wall locations
- Revised vs original clouding, so the city and the owner can see every change at a glance
- Structural and mechanical changes called out: moved beams, resized openings, relocated equipment, duct runs that differ from the permitted set
- Notes tying each cloud to the plan check comment or correction letter it resolves
- Title block with revision number, date, and verifier
- Schedules and sheet setup matching your office standard, so the set reads like your work, not a surveyor's
How to show changes: revision clouds and delta dimensions
Cloud every deviation from the issued set and tag it with a revision number that appears in the title block. Use delta dimensions only where the field measurement differs from the original, so the reviewer can spot the correction without hunting. If your team redlines in Revit, tools like Pretiva Studio can apply your clouding and sheet setup conventions overnight, though field verification stays on you. The same convention works for interiors packages, as covered at https://studio.pretiva.io/interior-designers.
How do as-built drawings differ across architecture, construction, and MEP disciplines?
Architecture and interiors
Your architectural as-builts are the set everyone else builds on: corrected wall locations, actual door and window sizes, ceiling heights, and finish notes that match the field. For a solo residential practice, the deliverable is usually a revised floor plan, exterior elevations, and a few details, clouded where the contractor deviated from the permit set. If you measure and draft these in-house, budget roughly the going market rate; published as-built service pricing commonly runs about $0.10–$0.25 per square foot (example published rates). When a builder hands you PDFs instead, your job shifts to reconciling their markups against your Revit model sheet by sheet.
Structural and MEP on residential jobs
Structural as-builts on single-family work are thin: anchor bolt locations, any field-cut joists, and the actual footing sizes if the inspector flagged them. Mechanical, plumbing, and electrical as-builts matter more at closeout, since homeowners need to know where shutoffs, panels, and duct runs ended up. If you also deliver documentation for builders, the same discipline split applies (https://studio.pretiva.io/builders).
Should you hire as-built drawing services or produce them in-house?
What outsourcing costs and what you give up
Measuring and modeling a 2,500 sq ft house yourself takes a day on site and a day in Revit, versus paying a contract drafter $1,400-$2,400 per set or an as-built service a comparable fee for less control. Outsourcing means someone else decides sheet setup, level names, and wall types, so you spend plan-check time fixing conventions that do not match your office standard. You also carry the liability either way: the field dimensions are yours to certify, whoever drafts them.
Where AI drafting fits and where it does not
AI drafting handles the modeling half, not the measuring half. Pretiva Studio works in your Revit, overnight, to your sheet setup and schedules, but it cannot verify field conditions. You still measure, and even iPhone Pro LiDAR measurements carry documented tolerance in Apple's own Measure app support notes, so corners, flush conditions, and remodeled areas need a tape or laser check. The honest split: AI drafts CDs from verified dimensions, you supply the dimensions. If you skip that step, no tool saves you from a correction letter.
What are the most common as-built drawing mistakes and how do you avoid them?
Five mistakes that generate rework
Assuming symmetry. A mirrored plan is a guess. Verify each side independently, because kitchens, additions, and past remodels are rarely symmetric.
Missing ceiling and roof changes. Bulkheads, raised ceilings, and rafter overhangs added after original construction are the items plan check reviewers and framers catch first. Photograph and dimension every transition.
No delta dimensions. Mark changed conditions with revision clouds and delta dimensions so the reviewer sees what moved, not just the final state.
Wrong datum. Mixing finished floor and structural slab elevations corrupts every height callout. Pick one datum per set and state it on the general notes.
Carrying unverified dimensions from old sets. A dimension on a 1998 drawing is a hypothesis. Field-verify anything you did not measure yourself.
A pre-delivery QC pass
Before issuing, walk the set against a short checklist: every dimension traced to a field measurement or a flagged assumption, one stated datum, clouds and deltas on all changed conditions, and ceiling/roof plans reconciled against site photos. One hour of checking beats one correction letter and a resubmittal.
FAQ
Are as-built drawings legally required for a residential remodel permit?
Not universally, but many jurisdictions require a corrected or as-built set before final inspection when field changes diverge from the permitted plans. Washington jurisdictions commonly do this. Requirements vary by city, so check the local building department's permit and revision requirements before deciding whether a full as-built set or a marked-up revision sheet satisfies the record.
How much do as-built drawing services charge per square foot?
Published as-built service pricing commonly runs about $0.10–$0.25 per square foot. For a 2,500 sq ft house, that lands in the same range as paying a contract drafter roughly $1,400–$2,400 per set. Doing the work yourself costs a day on site and a day in Revit, with full control over sheet setup and conventions.
Can I do as-built drawings from a phone LiDAR scan instead of measuring by hand?
For most rooms in a residential remodel, a phone with LiDAR plus a laser measure covers capture in an afternoon. But LiDAR measurements carry documented tolerance, so corners, flush conditions, and remodeled areas still need a tape or laser check. Photograph every wall with dimensions in frame, and note conditions a scan cannot explain, like patched openings or sagging beams.
Do as-built drawings need to be stamped by an architect?
If your design changed during construction, you document the changes and issue the as-builts under your seal. If the contractor made means-and-methods adjustments, they typically hand you a redline set, and you decide what merits a reissued sheet. Either way, the field dimensions are yours to certify, whoever does the drafting, so the deliverable carries your seal.
What is the difference as-built drawings and a survey?
A survey documents property boundaries, setbacks, and site conditions, usually produced by a licensed surveyor. As-builts document the building itself as constructed: wall locations, opening sizes, ceiling heights, and every deviation from the permitted set. For a renovation permit you typically need both, but they answer different questions and come from different disciplines with different liability.